Outdoor Part Help
How-to guide

How to clean a lawn mower carburetor, and when to replace it instead

Old fuel leaves varnish that blocks the tiny jets in a mower carburetor. The engine then surges, runs rough, only runs with the choke on, or will not start at all. Cleaning often fixes it; when the carburetor is badly gummed or corroded, a replacement is often cheaper than the time.

Updated November 16, 2026. Sales shares are estimates for July to October 2026.

2part types to check
22part numbers compared

Check these first

  1. Prepare. Turn off the fuel valve (or pinch the fuel line), pull the spark plug wire and take a photo of the linkage and springs before removing anything.
  2. Clean without full removal first: remove the float bowl (one bolt or nut underneath, over a pan), and spray carburetor cleaner into the bowl and up the center tube. Many mowers run again after just this.
  3. Clean the main jet. On most small engines it is in the bowl nut or the center tube. Spray cleaner through every hole and clear them with a thin wire or a nylon bristle. Do not drill or enlarge the jets.
  4. Check the float and needle. The float should move freely and the needle should seat; a sticking float floods the engine.
  5. Reassemble with a new bowl gasket, refit the air filter, add fresh fuel and test.
  6. Replace instead if the body is corroded, the jets stay blocked after cleaning, the throttle shaft is loose, or the engine still surges. Match the replacement to your engine model number.

Lawn mower carburetors

Most bought first, by share of estimated Amazon sales across 2 part numbers. All carburetor part numbers

  1. 1MTD 951-0514975% of sales

    Carburetor for MTD-built riding mowers such as the Huskee LT4200, Craftsman T1000 and T1200, and Cub Cadet CC30 and CC760ES.

    4 listings from 3 brands. Most-bought aftermarket: Powtol, HUZTL, ALRACALL.

    Compare 951-05149 replacements
  2. 2MTD 951-1442325% of sales

    Carburetor for the 159cc engine on MTD-built walk-behind mowers such as the Cub Cadet SC100, SC300 and SC500 and Troy-Bilt TB210.

    3 listings from 2 brands. Most-bought aftermarket: Carbhub, Haokixin.

    Compare 951-14423 replacements

Snow blower, trimmer and other small-engine carburetors

The same cleaning steps apply. Many of these fit the 208cc and 179cc engines on MTD-built snow blowers (Troy-Bilt, Craftsman, Cub Cadet); others fit 2-stroke trimmers.

Most bought first, by share of estimated Amazon sales across 20 part numbers. All carburetor part numbers

  1. 1MTD 753-0619024% of sales

    Carburetor for 2-stroke Troy-Bilt string trimmers such as the TB22 and TB32EC, and some Weed Eater models.

    5 listings from 5 brands. Most-bought aftermarket: Dalom, Ferilter, ALFUL.

    Compare 753-06190 replacements
  2. 2Husqvarna 54508184816% of sales

    Carburetor for Husqvarna 128-series trimmers (128C, 128L, 128LD, 128R). Also marked C1Q-W40A.

    3 listings from 3 brands, including Husqvarna's own part. Most-bought aftermarket: Ferilter, ALFUL.

    Compare 545081848 replacements
  3. 3MTD 951-1270513% of sales

    Carburetor for MTD-built 208cc snow blower engines, such as the Troy-Bilt Storm 2410 and 2620 and Craftsman 24-inch models.

    12 listings from 12 brands. Most-bought aftermarket: Pro Chaser, Joozur, fullas.

    Compare 951-12705 replacements
  4. Carburetor for Poulan Pro chainsaws such as the PP4218 and PP3816.

    2 listings from 2 brands. Most-bought aftermarket: Hipa, ALFUL.

    Compare 545070601 replacements
  5. 5MTD 951-152366% of sales

    Carburetor for the 208cc engine on snow blowers such as the Craftsman SB410 and Troy-Bilt Storm 2410. Also sold as 751-15236.

    9 listings from 9 brands. Most-bought aftermarket: laffoonparts, Pro Chaser, Eamonhigh.

    Compare 951-15236 replacements
  6. 6MTD 753-062886% of sales

    Carburetor for 25cc Troy-Bilt trimmers and blowers such as the TB2044XP, TB430 and TB225, and some Remington and Murray models.

    3 listings from 3 brands. Most-bought aftermarket: Harbot, Anxingo, Hettluo.

    Compare 753-06288 replacements
  7. Carburetor for Husqvarna 224L and 324L-series trimmers and some hedge trimmers.

    2 listings from 2 brands. Most-bought aftermarket: partszen, ALFUL.

    Compare 531008681 replacements
  8. 8MTD 951-14026A4% of sales

    Carburetor for MTD-built 208cc snow blower engines; listings give 951-05251, 951-12705 and 951-15236 as alternates.

    7 listings from 7 brands. Most-bought aftermarket: YAMAKATO, HOOAI, LIZAPUS.

    Compare 951-14026A replacements

More help

See the lawn mower won't start guide for the checks to do before touching the carburetor.

Safety

  • Work outdoors or in a ventilated area, away from flames: gasoline and carburetor cleaner are flammable.
  • Wear eye protection when spraying cleaner.

Frequently asked questions

What are the signs of a dirty mower carburetor?

Surging (engine speed rising and falling), running rough, only running on choke, hard starting, and starting then dying.

Can I clean a carburetor without removing it?

Often, yes: remove the float bowl, spray cleaner into the bowl and through the main jet. Remove the carburetor only if that does not fix it.

Should I clean or replace my mower carburetor?

Clean it first if it is only lightly gummed. Replace it if it is corroded, the jets stay blocked, or the throttle shaft is worn; replacements for common engines are inexpensive.

Do snow blower and trimmer carburetors clean the same way?

Yes, the steps are the same: float bowl, main jet, float and needle. Two-stroke trimmer carburetors have no float bowl; they use a diaphragm, so a rebuild kit or a replacement is often simpler.

As an Amazon Associate we earn from qualifying purchases. Sales shares are our estimates of Amazon sales and are rounded. Aftermarket parts are made by third parties, not by the makers. How this works