How to sharpen lawn mower blades, and when to replace them instead
A sharp blade cuts grass cleanly; a dull one tears it, leaving ragged brown tips, uneven cutting and strips of uncut grass. Most mowers need their blades sharpened once or twice a season (roughly every 20 to 25 hours of mowing), and replaced when they are bent, cracked or worn thin.
The steps below work for walk-behind and riding mowers. On a riding mower or zero-turn, it is often easier to lower or remove the deck first.
Check these first
- Make the mower safe. Switch off, let the engine cool and pull the spark plug wire off the plug (on a riding mower, also take the key out). On a walk-behind, tip it with the air filter and carburetor facing up so oil and fuel cannot leak into them.
- Mark and remove the blade. Mark the underside with paint or a marker so it goes back the same way up. Wedge a block of wood between the blade and the deck, then loosen the bolt (usually counter-clockwise) with a breaker bar.
- Sharpen the cutting edge only. Clamp the blade in a vise and file, or use a grinder lightly, along the original angle (usually about 30 degrees). Work from the inside to the tip, and stop at a butter-knife edge: razor-sharp edges dull faster.
- Balance it. Hang the blade on a nail or a cone balancer. If one side drops, take a little more metal off that side. An unbalanced blade shakes the mower and wears the spindle bearings.
- Refit it the right way up (the wings or sail point up toward the deck), and tighten the bolt to the torque in your manual.
- Replace instead of sharpening if the blade is bent, cracked, has deep nicks, the sail is worn thin, or it has been sharpened so often it is visibly narrower. Replace all blades on a multi-blade deck at the same time.
Riding mower blades, most bought first
Match the deck size, blade length and center hole. Multi-blade decks need a full set.
Most bought first, by share of estimated Amazon sales across 54 part numbers. All mower blade part numbers
Blades for many MTD-built 42-inch decks, including Cub Cadet and Troy-Bilt riding mowers. Also sold as 742-04308.
37 listings from 30 brands. Most-bought aftermarket: UDC Parts, Grasscool, ZALANA. Fits 42-inch decks.
Compare 942-04308 replacementsBlades for John Deere 42-inch decks. Listings name the D100, D105, D110, D130, E100 to E130 and LA100-series tractors, and the cross-reference GX22151.
28 listings from 24 brands, including John Deere's own part. Most-bought aftermarket: UDC Parts, Grasscool, JXJKCZ. Fits 42-inch decks.
Compare GY20850 replacementsBlades for MTD-built 50-inch decks: Cub Cadet ZT1, ZT2, XT1 and XT2 50-inch models and Troy-Bilt Super Bronco and Mustang 50. Usually sold as a set of three.
25 listings from 22 brands, including MTD's own part. Most-bought aftermarket: TENGMUJX, Grasscool, Hipa. Fits 50-inch decks, 6-point star center hole.
Compare 942-05052A replacementsBlades for John Deere 48-inch decks. Listings name the D140, D160, E140 and E170.
25 listings from 25 brands, including John Deere's own part. Most-bought aftermarket: Grasscool, UDC Parts, SCBHWJ. Fits 48-inch decks.
Compare GY20852 replacementsBlades for Husqvarna 46-inch decks such as the YTH22V46. Also sold as 405380.
22 listings from 22 brands. Most-bought aftermarket: Grasscool, UDC Parts, wyevee. Fits 46-inch decks.
Compare 532405380 replacementsBlades for MTD-built 46-inch decks such as the Cub Cadet XT1 LT46. Also sold as 742-04244.
33 listings from 29 brands, including MTD's own part. Most-bought aftermarket: Grasscool, UDC Parts, GICOOL. Fits 46-inch decks, 6-point star center hole.
Compare 942-04244A replacementsBlades for 54-inch decks on Husqvarna mowers such as the Z254F, and similar Craftsman and Poulan models. Also sold as 187256.
19 listings from 18 brands. Most-bought aftermarket: Grasscool, UDC Parts, BCQNXX. Fits 54-inch decks.
Compare 532187256 replacementsBlades for MTD-built 46-inch decks on many Cub Cadet riding mowers. Also sold as 742-04290.
37 listings from 32 brands, including MTD's own part. Most-bought aftermarket: UDC Parts, Grasscool, JYLEYJ. Fits 46-inch decks, 6-point star center hole.
Compare 942-04290 replacements
More on mower blades
See the full mower blade guide (deck sizes, high-lift vs mulching), the Craftsman and Cub Cadet blade guides.
Safety
- Always disconnect the spark plug wire before touching the blade.
- Wear thick gloves and eye protection when filing or grinding.
- Never straighten a bent blade. Replace it; a straightened blade can crack.
Frequently asked questions
How often should I sharpen my mower blades?
About once or twice a mowing season, or every 20 to 25 hours of use. Sharpen sooner if the grass tips look torn or brown after mowing.
Can I sharpen mower blades without removing them?
It is possible with a file on some walk-behinds, but removing the blade is safer and lets you balance it, which protects the mower's bearings.
When should I replace a mower blade instead of sharpening it?
When it is bent, cracked, deeply nicked, worn thin at the sail, or much narrower than new from repeated sharpening.
What is the most bought riding mower blade?
942-04308, at about 15% of estimated Amazon sales across the 54 blade numbers we compare.
As an Amazon Associate we earn from qualifying purchases. Sales shares are our estimates of Amazon sales and are rounded. Aftermarket parts are made by third parties, not by the makers. How this works